WB Color FX

WB Color FX


In stock (Message)

WB Color FX is a concentrated color that we designed specifically for WB Prime FX. It comes in 6 standard colors for you to choose from.

Used to easily tint any of our water-based epoxies. Use it in our water-based epoxy as a base coat/prime coat for metallic floors, epoxy flake floors, or solid-color epoxy floors.

  • Light Gray
  • Medium Gray
  • Sun
  • Buff
  • Black
  • White
SKU: WBcolorFX Category: Tags: , , , , ,


WB Color FX is a concentrated color that we designed specifically for WB Prime FX. It comes in 6 standard colors for you to choose from.

We use it to easily tint our water-based epoxies as a base coat/prime coat for metallic floors, epoxy flake floors, or solid-color epoxy floors. Our color is made of extremely fine particle pigments and in turn, will easily disperse into our water-based base coat primer or any of our other water-based epoxies.

Colors include: Light Gray, Dark Gray, Buff, Sun, Black, and White.

Be sure to mix the color into Part A for a minimum of 1-2 minutes. Only when the color has been thoroughly mixed for a minimum of 1-2 minutes should you combine parts A and B. We recommend using a squirrel mixer. If you see any foam after mixing, allow it to settle.

Sold in 32 oz. containers.

Solids Content 40% +/-1%
Pot Life 60-90 Minutes
Tack Free 30-45 Minutes
Foot Traffic 7-15 Hours
Heavy Traffic 2-6 Days
Optimum Re-Coat Window 4-7 Hours
Maximum Re-Coat Window 12-18 Hours
Dry Appearance Clear Medium Gloss Finish
VOC Content Less Than 19 Grams/Liter Mixed


If mixing less than a full kit, mix Part A and Part B separately with a stir stick, or low-speed mixer to ensure uniform distribution of all ingredients.

If adding color, mix a 32 oz container of WB Color FX into Part A (Even if using less than a full kit) and mix thoroughly for 2 minutes.

In a clean mixing container, blend 1 Part A and 1 Part B using a drill mixer for 2-3 minutes. Avoid creating a vortex in the material which could introduce air and/or moisture content to the mixture. Do not mix more than can be applied within the usable pot life time frame.

Be sure to scrape the sides and bottom of the mixing bucket.

As a final mixing step, we strongly recommend placing the mixed (A and B) material in a clean bucket and mixing for an additional 1-2 minutes.

*Coverage Rates

First Coat – Direct to Concrete: 200 – 300 ft per gallon
Second Coat – Over Existing Coating: 250 – 350 ft per gallon

*Coverage rates may vary depending upon surface porosity, texture, application method, and prior coating application.


We suggest using a shedless 3/8″ nap roller cover. Dip and roll from a roller pan. An 18″ roller is always suggested as it covers a larger area and helps prevent roller lines.

Start by placing the wet roller at one corner of an approximate 4′ x 4′ square and roll the material at an angle to the opposite corner applying no pressure to the roller. Spread the material across only that square and immediately back-roll to even out material and roller lines. Adjust the size of your square as needed based on the amount of material being applied with the roller.

After finishing the square, move on to the next square using the same technique. While applying keep a wet edge to prevent roller marks. It is recommended to work in sections usually using control joints as dividers to ensure proper application results. If the material becomes thick while applying and sticking to the roller, stop applying and discard the mixed material. At this point, it has reached the end of the usable pot life. Do not allow the material to puddle! Use a brush to remove the excess coating in joints. An airless or HVLP sprayer may also be used.

WB Prime FX will aid in completely sealing off the concrete surface and avoiding air bubbles.


For best results, it is always recommended to re-coat WB Prime FX as soon as one can walk onto the surface without imprinting or making an impression on the surface. This is typically within 4 – 6 hours. (This is especially true when re-coating with Xtreme FX or Base Coat FX.)

If possible, recoat within the suggested recoat window. Apply additional coats in the same manner as the first coat. Note that higher substrate, air, and material temperatures, as well as excessive humidity, may greatly reduce the acceptable recoat window of WB Prime FX. When working in higher temperatures, always recoat as early in the recoat window as possible to avoid failure between coats.

If recoating outside the suggested recoat window or beyond 24 hours, sand using a 220 grit or coarser sanding screen to ensure adequate adhesion between coats. Vacuum dust thoroughly, rinse with clean water, and remove excess water with a wet/dry vacuum or floor scrubber. Allow the surface to dry completely prior to application of the coating. Where applicable and with adequate ventilation, wipe the surface with acetone and a microfiber dust mop.

Go to Top